6DDT 2 Speed High Flow Skid Steer Auger Package with Mount - Digga

Overview

With 5,013 ft-lbs and a 30 inch ceiling in clay, the 6DDT two-speed high flow skid steer auger attachment sits in the middle of Digga's shifting range and costs about thirty dollars more at list than the 5DDT. On this page it comes three ways: Drive Only if you already have a frame, on the Universal Quick Attach Frame Package with 7 ft hoses and flush-face disconnects, or on the Extension Frame (TPE) Package, Digga's telescopic piling and drilling extension.

Key Features of the Digga 6DDT 2 Speed Skid Steer Auger Package

• Torque 5,013 ft-lbs at 3,000 PSI and 5,837 ft-lbs at 3,500 PSI, as published by Digga for the 6DDT
• Recommended flow 10-36 GPM, with 10 GPM the floor for rated torque
• 2.5 inch hex output shaft taking A6 earth auger bits, RC6 rock and earth combo bits and DR6 dedicated rock augers
• Drills to 40 inches in earth and 30 inches in clay or shale, subject to ground conditions
• Digga gearbox with an integrated pressure relief valve, so no external valve block and fewer joints to leak
• The gearbox follows the bit down the hole, so drive height is not lost from drilling depth
• HALO Alignment Kit optional — HALO built into the drive hood at the factory, reading plumb to ±0.25 degrees per Digga
• Shifts between high torque and high speed under load, without stopping or lifting out
• Case drain hose included; the machine needs the low-pressure return line
• 10 ft powerlead with a 2-pin connector fitted for the shift solenoid
• 5 year gearbox and 3 year motor warranty for drilling use, plus lifetime shaft pull-out cover

Digga 6DDT Specifications

Figures as published by Digga for the 6DDT. Maximum drilling diameter depends on ground conditions and is a guide rather than a rating.

Choosing How the 6DDT Mounts

The TPE is engineered for drives up to 16,000 ft-lbs, so the 6DDT sits well inside it. One thing to plan for: a drive working 12-14 ft down needs more hose than the 7 ft set, and Digga's TPE hose kits come in 14 ft and 16 ft for exactly that. Tell us if the package is for TPE work and we will confirm hose length with the order.

HALO Alignment Kit

Every 6DDT on this page — both frame options and Drive Only — can be taken with No HALO or with the HALO Alignment Kit. Despite the name it is not a bolt-on: choosing it supplies the 6DDT with HALO built into the drive hood at the factory, with the extension cable and in-cab 12V plug. A ring of green lights means plumb; red and green guide the operator back when the drive drifts. On a one-person crew it replaces the spotter at the hole.

What Comes in the 6DDT Skid Steer Package

• Digga 6DDT auger drive
• Universal skid steer frame and 75mm linkage, or the TPE extension frame, unless you choose Drive Only
• 7 ft hoses with flush-face quick disconnects on the frame package
• Case drain hose, required on every two-speed drive
• 10 ft powerlead with a 2-pin connector for the shift solenoid
• HALO where the HALO Alignment Kit is selected
• Not included: auger bits, and the Plug N Play Controller Kit needed to shift the drive from the cab

Where the 6DDT Sits in Digga's High Flow Range

Against the 5DDT, the 6DDT adds 23 percent more turning force and lifts the clay and shale ceiling from 24 to 30 inches, from the same minimum flow. The 7DDT above it is another 26 percent up, reaching 48 inches in earth against 40. The 6DDS is the single-speed version of the same size at 4,911 ft-lbs, without the shift, the case drain or the controller, and for considerably less. Max speed is 100 RPM, against 67 on the 6DDS.

Which Loaders Fit the 6DDT?

The 6DDT package mounts on the universal skid steer quick attach plate, so fitment is decided by hydraulics rather than brand. The 6DDT needs a high flow auxiliary circuit and at least 10 GPM to reach the torque above.

Add the 6DDT package to your cart to see delivered pricing for your address. Enter your machine make and model with the order and we check the fit before it ships.

Digga 6DDT 2 Speed Skid Steer Package Questions, Answered