3/4" TPE Hose Kit - Digga

3/4" TPE Hose Kit - Digga

When a Digga telescopic piling or drilling extension needs hydraulic reach beyond the machine, the right hose kit is a critical part of the setup. This genuine Digga 3/4" TPE Hose Kit is identified as the long hydraulic hose kit for the telescopic piling and drilling extension. It is designed for applications where the attachment operates at extended reach, including work described as driving 12 to 14 feet below the machine.

Product: 3/4" TPE Hose Kit - Digga
SKU: HS-002470
Hose size: 3/4"
Connection type: Flush-face quick disconnects
Application: Digga telescopic piling and drilling extension
Brand: Digga

The defining feature is its intended role as the long hose kit for an extension attachment. Telescopic piling and drilling work places the tool farther from the carrier than a standard close-in configuration. A hose kit suited to that extended setup helps connect hydraulic supply to the attachment across the required working reach. The stated 12-to-14-foot working depth is application context, not a confirmed hose length or a guaranteed maximum operating depth.

Flush-face quick disconnects are specified for the hose kit. These connectors provide the interface between the kit and compatible hydraulic connections, while their flush-face design helps limit exposed fluid at the coupling interface during connection and disconnection. Confirm that the connector configuration matches the machine and attachment before installation; the available product details do not specify coupler sizes, thread types, pressure rating, or flow rating.

This kit is intended for Digga telescopic piling and drilling extension use, rather than as a universal replacement hose for every skid steer attachment. Application fit depends on the extension model, hydraulic layout, connection requirements, routing path and required reach. Verify the exact Digga attachment model and hose arrangement against the existing setup. If replacing a worn or damaged hose, compare the connector ends and hose size with the part being removed before placing the kit in service.

Fit and installation considerations

• Check that the attachment is a compatible Digga telescopic piling or drilling extension.
• Confirm 3/4" hose size and flush-face quick disconnect compatibility with the machine and attachment circuits.
• Measure the required routing length on the actual setup; the product information identifies this as the long hose kit but does not give an overall hose length.
• Route hoses to avoid pinch points, sharp edges, excessive bending, abrasion and interference with telescoping or drilling movement.
• Before operation, inspect connections and hose routing, then check for leaks under the equipment manufacturer's recommended procedure.

Correct hose routing matters on an extension attachment. The hose needs sufficient reach for the intended movement without being stretched taut, trapped, or allowed to rub against moving components. Check the complete travel of the telescoping assembly and the working positions used on site. A hose that is too short can restrict movement; excess slack can snag or contact the attachment. Establish the routing and service loop required for the specific machine-and-extension combination rather than assuming reach from the stated working depth.

Hydraulic hose selection also depends on operating conditions. The listed 3/4" size alone does not establish pressure capacity, flow compatibility, temperature range, or fluid specification. Use the machine and attachment requirements when evaluating these factors. Do not substitute the kit based only on nominal hose size if the connection style, rating, or routing differs from the approved configuration. Installation and inspection should follow the equipment manufacturer's instructions and applicable shop safety procedures.

For replacement or setup planning, the most useful details to confirm are the Digga extension model, machine hydraulic requirements, connector configuration, and required hose route and reach. The product information establishes the kit as genuine Digga, identifies flush-face quick disconnects, and describes its long-hose application; it does not list included hardware beyond those details. Confirm any additional fittings or components needed for the particular installation before beginning service.

Listed as a skid steer and excavator attachment part, this Digga hose kit supports maintenance and setup of compatible telescopic piling and drilling equipment. The 3/4" TPE Hose Kit - Digga (HS-002470) is a focused component for extended-reach hydraulic connection—not a complete auger, extension, or machine. Matching the kit to the attachment and verifying hose reach, couplers, and hydraulic specifications helps keep installation aligned with the equipment configuration.