Festool 500368 Plane Router Bit KA 65 for Conturo

The Festool 500368 Plane Router Bit KA 65 for Conturo is a carbide-tipped router bit made for trimming excess edge banding flush to the panel surface. This is a router bit designed for flush trimming edge banding on flat and beveled workpieces. Model Number 500368. If you are doing finish work where sloppy overhang is not acceptable, this bit is built for that specific job.

In practical use, the main value here is control. The bit is intended to remove the extra edge banding material after application, leaving the edge clean and even instead of proud of the panel. Festool lists a 1-1/8" (28 mm) diameter and a 1/4" (7 mm) cutting height, which tells you this bit is focused on precise trimming rather than broad stock removal. That matters when you are working on veneered panels, finished sheet goods, or edge-banded parts that need a clean final pass.

The carbide-tipped construction is worth paying attention to because edge banding work can be repetitive, and a bit that holds its edge longer saves time and keeps results consistent. This bit uses a 2-flute design and an 8 mm shank, which fits the Festool routers and edge tools it was built around. It is a purpose-driven cutter, not a general all-around profile bit, and that is exactly why it makes sense for cabinet and finish applications.

Festool also specifies that it can be used for routing on the surface or in the edge area. That gives it flexibility for trim router work around panels and edge details, especially when you need flush trimming on beveled edges. That beveled-edge capability is the real differentiator here, because not every edge banding bit is set up to handle that kind of work cleanly.

On compatibility, this bit is suitable for the Festool OF 900, OF 1000, OF 1010, OF 1010 R, MFK 700, and MFKC 700. It also works with the KA 65 edge banding system. For buyers already working inside the Festool ecosystem, that matters because it keeps setup simple and helps you match the cutter to the router or edge banding process you are already using.

Who should buy it? Cabinet installers, shop guys doing panel work, finish carpenters, and serious woodworkers who use edge banding and care about the final look. If you just need a general trim bit, this is more specialized than you need. If you regularly flush trim edge banding, especially on beveled pieces, this is the kind of dedicated accessory that makes the job faster and the result cleaner.

Bit Type Bevel Trim Bit Material Carbide Tipped Shank Diameter 5/16" (8 mm) Cutting Diameter 1-1/8" (28 mm) Cutting Height 1/4" (7 mm) Overall Length 2.125 in Number of Flutes 2 Made In Germany

Festool 500368 Plane Router Bit KA 65 for Conturo is a specialist, and that is the whole point

If edge banding is part of your regular workflow, this bit makes a lot more sense than trying to fake the result with a general-purpose cutter.

• Who it's for: Cabinet shops, finish carpenters, and woodworkers trimming edge banding on panels and beveled parts.
• Why it stands out: It is purpose-built for flush trimming excess edge banding and works with a wide range of Festool routers that are already common in that kind of work.
• Worth knowing: This is not a general router bit for every job. It is a dedicated edge banding accessory, so it is best for buyers who know exactly what operation they need to do.

• What is this router bit designed to do? It is designed to remove excess edge banding material for flush trimming on flat or beveled pieces.
• What shank size does it use? It uses an 8 mm shank.
• Which Festool routers is it suitable for? Festool lists it as suitable for the OF 900, OF 1000, OF 1010, OF 1010 R, MFK 700, and MFKC 700.
• What are the cutter dimensions? The bit has a 1-1/8" (28 mm) cutting diameter and a 1/4" (7 mm) cutting height.