About this product
Pentair C176-59PZ Tank Body Assembly for Max-E-Glas II and Dura-Glas II Pumps
The Pentair C176-59PZ Tank Body Assembly is a genuine replacement pump housing / strainer body assembly for compatible Sta-Rite Max-E-Glas® II and Dura-Glas® II pool pumps. This assembly forms the front strainer section of the pump and helps house the pump basket, trap cover, and suction-side water flow entering the pump.
This replacement tank body is commonly used when the original pump body is cracked, leaking, drawing air, damaged from freeze expansion, damaged from overtightened fittings, or worn from age and service. Replacing the tank body assembly can help restore proper suction, reduce air leaks, and improve pump priming performance.
Product Features
- Genuine Pentair / Sta-Rite replacement part
- Manufacturer part number: C176-59PZ
- Tank body assembly for Max-E-Glas® II and Dura-Glas® II pumps
- Forms the pump strainer / trap body section
- Commonly listed as including the trap cover, cover O-ring, and strainer basket
- Helps correct cracked pump body, air leak, suction leak, and prime-loss issues
- Designed for pool and spa pump repair and rebuild applications
Product Details
Brand Pentair / Sta-Rite Part Number C176-59PZ Product Type Pump Tank Body Assembly / Strainer Body Assembly Pump Series Max-E-Glas® II / Dura-Glas® II Application Pool and spa pump housing repair Common Included Components Tank body, trap cover, cover O-ring, and strainer basketCompatibility
- Sta-Rite Max-E-Glas® II pump applications requiring part number C176-59PZ
- Sta-Rite Dura-Glas® II pump applications requiring part number C176-59PZ
- Compatible pump models where the original parts diagram calls for C176-59P or C176-59PZ tank body assembly
- Select P4R, P4RA, P4E, and P4EA series pump applications when matched by parts diagram
Common Signs This Part May Need Replacement
- Pump body is cracked or visibly damaged
- Pump loses prime or pulls air at the front housing
- Water leaks from the tank body or strainer pot area
- Threaded plumbing connections are cracked or stripped
- Trap body was damaged by freeze expansion or overtightened fittings
- Basket area, lid sealing surface, or housing is warped or worn
Important Notes
- This item is the tank body assembly for compatible Max-E-Glas® II and Dura-Glas® II pumps.
- Verify the exact included components before ordering, as packaging may vary by supplier or revision.
- Motor, seal plate, diffuser, impeller, shaft seal, clamp, plumbing unions, drain plugs, and mounting hardware are sold separately unless otherwise stated.
- Confirm your pump model, pump series, and existing part number before ordering.
- This part is not universal for all Sta-Rite, Pentair, Dura-Glas, Max-E-Glas, or Max-E-Pro pumps.
- If the seal plate, clamp, diffuser, impeller, or plumbing connections are also damaged, replacing the tank body alone may not fully correct leaks or priming issues.
Installation Notes
- Turn off power to the pump at the breaker before servicing.
- Relieve system pressure and drain the pump before disassembly.
- Disconnect plumbing carefully to avoid damaging connected fittings or pipes.
- Inspect the seal plate, clamp, diffuser, impeller, shaft seal, and O-rings during service.
- Replace worn seals and O-rings whenever the pump is opened for repair.
- Make sure the tank body seats evenly against the seal plate before tightening the clamp.
- Do not overtighten threaded plumbing fittings into the new tank body.
- Prime the pump completely before restarting to prevent dry-run damage.
- After installation, check for air leaks, water leaks, abnormal noise, and proper pump prime.
Related Products
- Pentair C176-59PZ Max-E-Glas II / Dura-Glas II Tank Body Assembly
- Pentair C3-185PZ Dyna-Glas / Max-E-Glas II 6" Strainer Cover
- Pentair R38006 / C8-58P Sta-Rite Max-E-Glas II Strainer Basket
- Aladdin O-12 Max-E-Glas II / Super II Strainer Cover O-Ring
- Aladdin GO-KIT38 Seal Kit for Pentair Sta-Rite MaxiGlas / DuraGlas
- U.S. Seal PS-201 3/4" Pump Shaft Seal
- Pentair C203-194P Seal Plate Kit
Maintenance Tips
- Keep the pump basket clean to reduce strain on the pump and tank body.
- Inspect the lid O-ring regularly and lubricate with pool-safe silicone lubricant when needed.
- Do not run the pump dry, as heat buildup can damage pump internals and sealing surfaces.
- Avoid overtightening plumbing fittings into plastic pump housings.
- Address suction-side air leaks quickly to help prevent cavitation, prime loss, and pump damage.
- Maintain proper water level and clear suction lines to protect the pump from running without adequate flow.
Description supplied by Aqua Pool Supply through its current Shopify listing. Product, performance, and health claims are the seller’s and have not been independently verified by StorkScout.
