Skip to main content

Minwax® 33333 Water Based Polycrylic® Protective Finish, 11.5 Oz, Clear Satin

Sold by Toolbox Supply

Minwax® 33333 Water Based Polycrylic® Protective Finish, 11.5 Oz, Clear Satin
$18.99

Opens toolboxsupply.com in a new tab. The seller handles checkout, shipping, and returns.

We may earn a commission when you buy through product links. Sponsored labels identify paid placements from Shopify. We select the Weekly Edit independently. How we make money

Price and availability requested live for this page. Final details are set by the seller.

Share

A closer fit

Find this, but…

Start with this listing, then change what matters. Matches come live from independent Shopify shops and are separate from StorkScout’s Weekly Edit.

Searches start with new, available products that ship to and from the U.S.

What would suit you better?

Try “folds for air travel” or “same shape, without plastic.”

About this product

Polycrylic® Protective Finish is a crystal clear, ultra fast-drying protective topcoat. Protects and adds beauty to interior wood surfaces including woodwork, furniture, doors and cabinets. Crystal clear finish is ideal for use over light woods like maple, ash and birch as well as over Minwax® Water Based Wood Stains. Dries quickly. Cleans up easily with warm water.

  • Size: 11.5 Oz
  • Protects and adds beauty to interior wood surfaces including woodwork, furniture, doors and cabinets
  • Crystal clear finish is ideal for use over light woods like maple, ash and birch as well as over
  • Minwax® Water Based Wood Stains
  • Dries quickly
  • Cleans up easily with warm water.

Specifications:

  • Sheens: Satin
  • Application Tool: Synthetic bristle brush
  • Location: Interior wood surfaces
  • Recoat: After 2 hours
  • Dry Time: 3 hours for light handling, 24 hours for normal use
  • Cleanup: Soap and warm water
  • Coverage: 125 sq. ft. per quart
  • Coats: 2-3
  • VOC Content: Maximum VOC of 275 g/L.

Recommended Uses:

  • Woodwork, furniture, cabinets, doors, not recommended for floors.

Directions:

  • Surface must be dry and free of wax, grease, polish, old finishes in poor condition or any foreign matter
  • Sand to a smooth, uniform surface. DO NOT USE STEEL WOOL. Remove dust with a cloth dampened with water or mineral spirits. Let dry completely
  • If desired, apply Minwaxr Wood FinishT or Minwaxr Water Based Wood Stain to unfinished interior wood surfaces following label directions. Wait at least 24 hours before applying Polycrylicr over Minwaxr Wood FinishT
  • Shake can vigorously for two minutes. Repeat for 10 seconds after each minute of use
  • Protect adjacent areas from overspray. Hold can vertically 12 inches from surface and depress button fully. Spray using an even, sweeping motion with slightly overlapping strokes. On unfinished wood, apply sufficient material to seal, open joints, edges and end-grain
  • Apply thin coats to avoid runs and sags. Allow product to dry at least 30 minutes between coats. Sand lightly with very fine sandpaper (220 grit) and remove all dust before applying next coat. At least 3 coats are recommended. If unable to recoat within 1½ hours, wait at least 72 hours then lightly sand and recoat
  • Polycrylic® dries to the touch in 30 minutes and can be handled after 1 hour. After final coat, allow 24 hours before normal use.

FAQ's:

Why does Minwax® Polycrylic® Protective Finish appear milky in the can?

  • The milk-white appearance is caused by the scattering and reflection of light striking the liquid and the particles suspended in it. The slight haziness disappears on the wood leaving a clear finish.

Can Polycrylic® be used over Minwax® Wood Finish™ stains?

  • Yes, provided the Wood Finish™ has dried completely, which generally takes 24 hours. The one exception is over Wood Finish™ Red Mahogany Stain. Polycrylic® and Red Mahogany are not compatible.

When applying Polycrylic® over wood that has not been sealed with a wood stain, how can grain raising be minimized?

  • Sand the wood prior to applying Polycrylic®. Before the final sanding, moisten the wood with a rag or sponge dipped in water. Allow the wood to dry, then sand off the raised grain with #220 sandpaper. After wiping off the dust, apply Polycrylic®.

Should Polycrylic® be sanded between coats?

  • Yes. A light sanding (#220 sandpaper) will remove any fine particles of dust which settle on the finish while it is still wet. Light sanding also helps abrade the surface, improving intercoat adhesion.

Can I use steel wool in place of fine sandpaper?

  • No. Since steel wool and water can cause rust, steel wool should be avoided around all water-based wood finishing products. A stray strand lodged in the surface could leave an unsightly stain in the wood.

Warning:

  • If you scrape, sand or remove old paint, you may release lead dust. Lead is Toxic. Contact the National Lead Information Hotline at 1-800-424-LEAD or log onto www.epa.gov/lead.

Description supplied by Toolbox Supply through its current Shopify listing. Product, performance, and health claims are the seller’s and have not been independently verified by StorkScout.