About this product
Function
This air compressor solenoid valve unit, also known as an air compressor valve block, directly replaces the original unit on specific vehicles. It restores proper suspension performance when the original unit fails.
Features and Benefits
Direct Fit Replacement - Guaranteed to fit and function for your specific application
Highest Quality Materials
Quality Tested - built to a strict level of product standards.
Strict quality requirements
During the entire production process, all our parts are subject to strict quality control. In each step of production, a number of quality control checks are performed to ensure that each part can be used for many years.
Product Specifics
Type: Air Suspension Strut
Fitment Type: Direct Replacement
Size: Single Dimension(CM) 80(Length)*19(Width)*19(Height)
Single Weight(KG): 11
Maximum Operating Pressure (psi): 160
Minimum Operating Pressure (psi): 90
Package: Box
Modified Item: No
Included Hardware: None
Drive Layout: Front Engine AWD/4WD
Platform: W222
Custom Bundle: No
Material: Iron+Aluminium Alloy+Rubber
Quantity: 1 PC
Manufacturer Warranty: 1 Year
OE Spec or Performance/Custom: OE Spec
Adjustable: Yes
Features: Sealed
Brand: ECCPP
UPC: Does not apply
Manufacturer Part Number: E115781CP01
Interchange Part Number: 2223208113 2223204913,222-320-4913,2223208113A
Other Part Number: 222-320-8113,222 320 4913,222 320 8113
Superseded Part Number: A2223204913, A2223208113,A222-320-4913
Return Policy: 30 Days Free Return Or Exchange
Surface Finish: High Quality
Replacement Part Number:
2223208113,2223204913,222-320-4913,
222-320-8113, 222 320 4913, 222 320 8113,
A2223204913, A2223208113, A222-320-4913,
A222-320-8113, A222 320 4913, A222 320 8113
5.Reinstall the bottom mount bolt and nut. tighten to manufacturers specifications.
6.Install the three (3) top mount nuts provided in the accessory kit. tighten to manufacturers specifications.
7.Connect the two (2) electrical connectors to the new strut solenoid.
8.Reinstall the strut wire harness using the provided zip tie and reroute the lines.
9.Push the air line into the air fitting on the top of the strut until it is fully sealed/seated
10.Reinstall the applicable engine bay trim.
11.Reinstall the front left wheel.
12.Inflate the air strut per manufacturers specifications.
13.Lower the vehicle.
14.Installation complete.
Removal Guideline
Caution: Damage to the vehicle and air suspension system can be incurred if work is carried out in a manner other than specified in the instructions or in a different sequence.
To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
Consult your vehicle owner's manual,service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
Once the vehicle has been raised from the ground, put vehicle in neutral, and then back into park to release the tension on the drivetrain.
1.To avoid the possibility of short circuits while working with electric components consult your owner's manual on how to disconnect your battery.
2.Consult your vehicle owner's manual, service manual, or car dealer for the correct jacking points on your vehicle and for additional care, safety and maintenance instructions. Under no circumstances should any work be completed underneath the vehicle if it is not adequately supported, as serious injuries and death can occur.
1.Raise vehicle at lifting points prescribed by manufacturer
2. Remove applicable engine baytrimto gain accesstothetop strut mount.
3.Slowly disconnect air line fitting fromthetop ofthe strut.
4.Remove used air line fitting from the air line and discard. use the figure below as an example.
5.Remove front left wheel.
6.Disconnect the two (2) electrical connectors from the strut.
7.Unroute the lines and disconnect the strut wire harness from the lower mount of the
strut.
8.Remove lower strut bolt and nut.
9.Remove the three (3) top mount nuts.
10.Remove bolt and nut from spindle and disconnect.
11.Remove the strut from the vehicle.
12.Remove top mount plate from the strut. this will be reused in the installation.
13.Removal complete.
Installation Guideline
1.Removethe shipping plug fromthe check valve and install the voss fitting from the provided accessory kit on to the arnott air strut. remove the shipping pin from the voss fitting.
2.Install the top mount plate on to the new strut.
3.Install the arnott strut in the vehicle.
4.Reconnect the spindle to install the bolt and nut. tighten to manufacturers
Installation Recommended
If you are not professional, please ask your mechanic to fix it.
Note
1 year warranty for any manufacture defect.Please provide photos or videos to apply for warranty.
Please inspect this part carefully prior to installation and contact us with any questions before attempting to install it.
Please double confirm the compatibility as well as the OEM number before purchasing.
These air suspension solenoid valves are aftermarket parts. They will replace the original ones.
If you are not sure whether our parts fit you should contact us before buying,we will confirm for you.
Professional installation is recommended.
Contact us please for whatever we can help.
Includes
Single for Front Left Air Suspension Shock Strut
Description supplied by Dynamic Performance Tuning through its current Shopify listing. Product, performance, and health claims are the seller’s and have not been independently verified by StorkScout.
