Festool Drill Dust Collection Nozzle (500483)

The Festool 500483 Drill Dust Collection Nozzle is a drilling dust nozzle designed for cleaner drilling in floors, walls, and ceilings. Model Number 500483. If you are drilling overhead, drilling into masonry, or working inside finished spaces where dust gets everywhere fast, this attachment solves a real problem by pulling debris at the source while you work.

This is a drill dust collection nozzle designed for dust control during drilling. Festool rates it for drill bit diameters up to 1/2" (12 mm), which puts it right in the range for many common anchor holes and general drilling tasks. Used with a compatible dust extractor or standard vacuum, it helps reduce both falling dust and airborne debris, which is the part that usually turns a quick hole into a cleanup job.

What makes this nozzle more useful than a basic vacuum adapter is how it is built to stay against the work surface. Festool uses a patented dual-chamber system to support a cleaner drilling process and a more secure hold. There is also a foam rubber pad that helps it seal and hold on uneven surfaces, so you are not limited to perfectly flat material. That matters when you are drilling block, concrete, textured walls, or overhead surfaces that are never as clean and flat as they look on paper.

The flexible joint piece is another detail that earns its keep on the job. Instead of the hose fighting your drilling angle, the joint lets you move the hose into a better position. That makes the setup less awkward when you are drilling near corners, above shoulder height, or in places where hose management usually slows you down.

Festool also gives this accessory a nickel-plated steel drill sleeve, which is the kind of material choice you want on a part that sees repeated bit contact. The dust extraction connection fits 27 mm to 36 mm hoses, and Festool states it is compatible with all standard industrial and domestic vacuum cleaners. It is also listed as suitable for Festool KHC-S 18, KHC 18, BHC 18, PDC 18, TPC 18/4, and PD 20 drills, along with CTM dust extractors. If you are using an extractor with automatic filter cleaning, Festool notes that feature must be deactivated for this application.

This accessory makes the most sense for contractors and serious DIY users who drill indoors, in occupied spaces, or anywhere dust containment matters. It is especially useful for concrete drilling, anchor installation, electrical rough-in, mechanical work, and remodeling where you want to keep cleanup under control. If you already run a Festool dust extractor or a vacuum with a matching hose size, this is a simple add-on that can save time and keep the job looking more professional.

Category Drilling Dust Nozzle Dust Extraction Connection Diameter 1-1/16"-1-7/16" (27-36 mm) Maximum Drill Bit Diameter 1/2" (12 mm) Material Nickel-Plated Steel Drill Sleeve Overall Length 11 in. Overall Width 5 in. Weight 0.4 lbs Made In Germany

Festool 500483 Drill Dust Collection Nozzle Keeps Mess Under Control

This is the kind of accessory that seems small until you use it on a real job and realize how much cleanup it saves.

• Who it's for: Pros and serious DIY users drilling into concrete, masonry, walls, or ceilings where dust control actually matters.
• Why it stands out: The dual-chamber design, foam pad, and flexible hose joint make it more usable than a basic vacuum attachment, especially on uneven surfaces and overhead work.
• Worth knowing: The Festool 500483 Drill Dust Collection Nozzle is built for bits up to 1/2 inch, and if you are running an extractor with automatic filter cleaning, you need to turn that feature off for this setup.

• What size drill bits can this nozzle handle? It is rated for drill bit diameters up to 1/2" (12 mm).
• What hose sizes fit this drilling dust nozzle? The dust extraction connection fits 27 mm to 36 mm hoses, or about 1-1/16 inch to 1-1/4 inch.
• Can it be used with standard vacuums? Yes. Festool states it is compatible with standard industrial and domestic vacuum cleaners.
• Which Festool drills is it suitable for? Festool lists KHC-S 18, KHC 18, BHC 18, PDC 18, TPC 18/4, and PD 20.