ANBO GR200-8 Tractor Grapple Rake - 8" Tines

📘 Overview

The ANBO GR200-8 is a grapple attachment for tractor rated to 200 horsepower, supplied in 5 widths from 83" to 118" on 8-inch tine spacing. It is built for high-horsepower tractors and wheel loaders up to 200 horsepower. 8-inch spacing is the middle spacing — it sheds loose dirt on the lift while still holding logs and heavy brush, which suits the GR200-8 to brush piling, log handling and land clearing where dirt-free loads matter. The GR200-8 uses shorter root-rake tines in 1" AR400F steel, with a clamshell top grapple that closes over raked material so a load can be back-raked, gripped and carried in one pass. The choice you make on this listing is width — 83", 91", 100", 109", 118" — so pick the widest unit your loader can still lift full. Every ANBO grapple is built in Colville, Washington from American AR400F steel, ships with a mount fabricated for your own machine plus hoses and couplers, and carries a two-year attachment warranty with three years on the cylinders.

⚙ GR200-8 Key Features

• Rated to 200 horsepower — ANBO sizes each model to the machine, so the GR200-8 is matched to loaders and tractors up to 200 hp rather than sold by width alone.
• 8-inch tine spacing — sheds loose dirt on the lift while still holding logs and heavy brush.
• 1" : 1" AR400F tines — outer to inner tine thickness on the GR200-8, in steel with a 150,000–180,000 PSI yield strength against 32,000 PSI for A36.
• 58" grapple opening — the jaw span of the GR200-8 when the clamshell is open.
• 3.5"x 10" hydraulic cylinders — fully welded, rear mounted and rated to 3,000 PSI, with a built-in pressure relief valve on the larger units to protect the machine's hydraulics.
• Clamshell design with a top grapple — the top bar closes over raked material, so the unit rakes, digs, grips and back-rakes without an attachment change.
• Greaseable, accessible pivot points — every pivot takes grease and can be reached without dismantling the rake.
• 2-wire R-16 hoses rated to 5,800 PSI — routed securely, with hose wrap offered to protect the supply lines.
• Two-piece mount, engineered position — most ANBO mounts are two-piece, keeping the center of the rake open for visibility; mount location and angle are set to work on both tractors and skid steers.
• Made in the USA from American steel — designed, fabricated and assembled in Colville, Washington.

🔑 Why Buyers Choose the GR200-8

• AR400F is five times stronger than grade 36 steel — ANBO reaches the required strength without the extra plate thickness a mild-steel grapple needs, so the GR200-8 does not spend your 200 hp machine's lift rating on itself.
• 8-inch spacing decides what stays in the load — on the GR200-8 it sheds loose dirt on the lift while still holding logs and heavy brush, which is why this spacing is the one to pick for brush piling, log handling and land clearing where dirt-free loads matter.
• The top grapple lets you back-rake and carry in the same pass — material raked up is clamped and moved without swapping to a bucket, which removes a machine trip per pile.
• Greaseable pivots instead of sealed or welded ones — the wear points on the GR200-8 can be serviced on schedule, which is what decides whether a grapple lasts a season or a decade.
• Three years on the cylinders, one more than on the attachment — ANBO warrants the highest-wear hydraulic component for longer than it warrants the frame.

📊 ANBO GR200-8 Specifications — Grapple Attachment for Tractor

Specification Value Model ANBO GR200-8 Series Grapple Rake Machine rating Up to 200 horsepower Tine spacing 8" Widths available 83" – 118" (5 widths) Tine size (outer : inner) 1" : 1" Tine material AR400F abrasion-resistant steel, 150,000–180,000 PSI yield Grapple opening 58" Hydraulic cylinders 3.5"x 10" Cylinder pressure rating 3,000 PSI Hydraulic hoses 2-wire R-16, 5,800 PSI rating Pivot points All greaseable Design Clamshell with top grapple Warranty 2-year attachment, 3-year cylinders Country of origin United States — Colville, Washington

🔄 GR200-8 Specifications by Width

Every width on this listing, with its part number. Published weights are shown where ANBO lists them for that width. Freight is calculated at checkout on every width, published weight or not, so you will see the exact shipping cost before you pay.

Part number Width Attachment weight Cylinders GR200-8-83 83" Not published — GR200-8-91 91" 1,739 lb 3.5"x 10" GR200-8-100 100" 1,857 lb 3.5"x 10" GR200-8-109 109" 1,976 lb 3.5"x 10" GR200-8-118 118" 2,094 lb 3.5"x 10"

📋 Choosing Your GR200-8 Width

This listing covers the GR200-8 — tine spacing is fixed at 8" Tines across every part number on the page. The width option is the selection you make at checkout:

• 83" — part number GR200-8-83
• 91" — part number GR200-8-91, 1,739 lb attachment weight
• 100" — part number GR200-8-100, 1,857 lb attachment weight
• 109" — part number GR200-8-109, 1,976 lb attachment weight
• 118" — part number GR200-8-118, 2,094 lb attachment weight

A wider GR200-8 covers more ground per pass and weighs more. Match the width to what your loader can lift full, not to the widest unit offered.

🔗 What Is the ANBO GR200-8 Used For?

ANBO builds the Grapple Rake line for brush piling, log handling and land clearing where dirt-free loads matter. On the GR200-8 specifically, the jobs it is bought for are:

• High-horsepower land clearing
• Rock and stump removal
• Log and brush handling
• Root grubbing
• Farm and commercial site work

The GR200-8 ships complete and ready to run — the grapple, the mount built for your machine, hoses and couplers.

Buyers shop this class of attachment under several names. Root rake for tractor and grapple rake attachment both describe what the GR200-8 is — a clamshell rake that grips. If your search started with brush grapple, clamshell grapple or skid steer grapple rake, the GR200-8 is the 200-horsepower unit in that family.

🚜 Which Machines Fit the ANBO GR200-8?

The ANBO GR200-8 is built to order with a mount made for your specific machine. It is not a fixed-interface attachment: ANBO fabricates the mount to the loader, tractor or skid steer you name when you order, so fitment is confirmed at build time rather than assumed from a standard.

Fitment factor ANBO GR200-8 Machine horsepower Up to 200 hp — this is the primary fitment limit on the GR200-8 Machine types High-horsepower tractors and wheel loaders up to 200 horsepower Grapple opening 58" — the largest single piece the GR200-8 will close on Mount Custom-built to your machine. Universal skid steer quick attach and John Deere are the common options; ANBO builds most other mounts as well Mount construction Two-piece on most units, which keeps the center of the rake open for visibility. Build-backs reduce lift capacity and are only used where a machine requires one Hydraulics required One double-acting auxiliary hydraulic circuit to open and close the grapple. Cylinders are rated to 3,000 PSI Supplied with Mount, hoses and couplers

Horsepower is the deciding number, not width: ANBO names each model for the machine size it is built for, and running a 200-hp-rated grapple behind a bigger machine is what bends attachments. You do not need to check with us first: the order page asks for your machine make and model, we build the mount to it, and we verify fitment before the unit ships.

❓ ANBO GR200-8 Questions, Answered